APRILIA RSV4 R Service Station Manual Download Page 197

Page: 197 / 475

•

A correct throttle rotation cannot be detected given low ambient and engine temperatures:

some ice may have formed in the duct (at each key ON). The instrument panel does not

indicate the presence of this error even in the ATT status

Troubleshooting

•

Check that the throttle body is clean and that there is no ice or condensation in the intake

duct. If OK, replace the throttle body

Rear throttle power supply voltage during self-learning P0164

•

low supply voltage

Error cause

•

The throttle power supply voltage is too low to carry out the self-acquisition test correctly (at

each key ON). The instrument panel does not indicate the presence of this error even in the

ATT status

Troubleshooting

•

Delete errors hindering throttle self-learning.

Rear throttle position error P0167

•

misalignment between control and activation

Error cause

•

The throttle mechanical control may be damaged

Troubleshooting

•

Replace the throttle body

Front throttle Limp Home self-acquisition P0180

•

failed test

Error cause

•

Throttle position, kept by the springs, not within the expected field (at each key ON). The

instrument panel does not indicate the presence of this error even in the ATT status

Troubleshooting

•

Check if the throttle body and the intake duct are clean. If OK, replace the throttle body

Front throttle mechanical springs self-acquisition P0181

•

failed test

Error cause

•

Return time of the throttle, kept in position by the springs, not within the expected limits: the

causes can be a deterioration of the performance of the springs or excessive throttle friction

(at each key ON)

Troubleshooting

RSV4 R

Electrical system

ELE SYS - 197

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands

APRILIA RSV4 R, Service Station Manual

Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands