manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 407 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 407

•

Fit the washer on the screw

•

Tighten the screw.

•

Install the rear shock absorber and the

linkages.

•

Fit the rear brake calliper plate.

•

Fasten the two pipe grommets on the

swingarm

•

Install the rear wheel and the exhaust system.

•

Fit the pinion casing.

•

Adjust the chain tension

Drive chain

Adjusting

The vehicle is fitted with an endless chain, without master link.

NOTE

CARRY OUT MAINTENANCE OPERATIONS AT HALF THE INTERVALS SPECIFIED IF THE VE-
HICLE IS USED IN PARTICULAR RAINY OR DUSTY CONDITIONS, OFF ROAD OR FOR TRACK
USE.

CLEARANCE CHECK

To check clearance:

•

Shut off the engine.

•

Rest the vehicle on its stand.

•

Engage neutral gear.

•

Check that the vertical oscillation at a

point between the pinion and the

sprocket on the lower branch of the

chain is around 30 mm (1,18 in).

RSV4 R

Chassis

CHAS - 407

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments