manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 2 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 2

SERVICE STATION

MANUAL

RSV4 R

THE VALUE OF SERVICE

Due to the continuous technical updates and specific mechanic training programs for aprilia products,

only 

aprilia Official Network

 mechanics know this vehicle fully and have the special tools necessary to

carry out maintenance and repair operations correctly.

The reliability of the vehicle also depends on its mechanical state. Checking the vehicle before riding, its

regular maintenance and using only 

Original aprilia Spare Parts

 are essential!

For information about the nearest 

Official Dealer and/or Service Centre

, consult the Yellow Pages or

search directly from the map on our Official Website:

www.aprilia.com

Only by requesting aprilia Original Spare Parts can you be sure of purchasing products that were

developed and tested together with the actual vehicle itself. All aprilia Original Spare Parts undergo

quality control procedures to guarantee reliability and durability.

The descriptions and illustrations given in this publication are not binding; While the basic characteristics
as described and illustrated in this booklet remain unchanged, aprilia reserves the right, at any time and
without being required to update this publication beforehand, to make any changes to components, parts

or accessories, which it considers necessary to improve the product or which are required for

manufacturing or construction reasons.

Not all versions/models shown in this publication are available in all Countries. The availability of

individual versions/models should be confirmed with the official aprilia sales network.

© Copyright 2009 

aprilia

. All rights reserved. Reproduction of this publication in whole or in part is

prohibited. 

aprilia

 - After-sales service.

Aprilia trademark is property of Piaggio & C. S.p.A.

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments