manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 429 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 429

•

Screw the bleed valve and remove the

pipe.

•

Top-up the reservoir until the right

brake fluid level is obtained.

•

Refit and block the front brake fluid res-

ervoir cap.

•

Refit the protective rubber cap.

Rear

Any air trapped in the hydraulic circuit acts as a cushion, absorbing much of the pressure applied by

the brake pump and minimising the braking power of the calliper.

Air in the system causes a "spongy" feeling in the brake control and poor braking efficiency.

CAUTION

CONSIDERING THE DANGER FOR VEHICLE AND RIDER, IT IS STRICTLY NECESSARY, AFTER
REFITTING BRAKES AND RESTORING THE BRAKING SYSTEM TO THE REGULAR USE CON-
DITIONS, THAT THE HYDRAULIC CIRCUIT BE AIR PURGED.

NOTE

THE VEHICLE MUST BE ON LEVEL GROUND TO BE PURGED. WHILE PURGING THE HYDRAUL-
IC SYSTEM, FILL THE RESERVOIR WITH THE NECESSARY QUANTITY OF BRAKE FLUID.
CHECK THAT, DURING THE OPERATION, THERE IS ALWAYS BRAKE FLUID IN THE RESER-
VOIR.

•

Remove the rubber protection cover

from the bleed valve.

•

Insert the transparent plastic pipe in

the rear brake calliper bleed valve and

insert the other end of this pipe into a

container to collect the fluid.

•

Remove the rear brake fluid reservoir

cap.

•

Operate the brake lever and then open

the bleed valve on the calliper by a 1/4

turn to let the air escape.

•

Close the bleed valve before reaching

the end of travel of the brake lever,

then repeat the operation until air no

longer escapes.

•

Screw the bleed valve and remove the pipe.

•

Top-up the reservoir until the right brake fluid level is obtained.

RSV4 R

Braking system

BRAK SYS - 429

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments