APRILIA RSV4 R Service Station Manual Download Page 165

Page: 165 / 475

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (for example, the pipe

between sensor and throttle body is squashed or there is a hole in the intake manifold).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean.

Estimation error for rear cylinder intake manifold pressure P0215

•

too high pressure/too low pressure.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean: there is an evident defect in the intake and pressure reading systems.

Estimation error for front cylinder intake manifold pressure P0216

•

too high pressure/too low pressure.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean: there is an evident defect in the intake and pressure reading systems.

Pressure too low at rear cylinder manifold error P0217

•

signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is below the estimated one (for example, smeared throttle

body).

Troubleshooting

RSV4 R

Electrical system

ELE SYS - 165

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands

APRILIA RSV4 R, Service Station Manual

Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands