manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual

The APRILIA RSV4 R Service Station Manual is an essential tool for motorcycle enthusiasts. This comprehensive manual provides users with detailed instructions on all aspects of servicing and maintaining their RSV4 R. Download this manual for free at manualshive.com and keep your bike running smoothly for years to come.

Share
Download
background image

•

Fit the two new pads in the correct po-

sition.

ALWAYS REPLACE THE FOUR PADS AND MAKE SURE
THEY ARE CORRECTLY POSITIONED INSIDE THE CAL-
LIPER.

•

Fit the front brake calliper on the disc.

•

Hand-tighten the two screws (1) fully.

•

Pull the front brake lever to seat the

brake calliper correctly.

•

Tighten the two screws (1).

•

Check the front brake fluid level.

Rear brake pads

Removal

•

Rest the vehicle on its stand.

•

Remove the rear brake calliper.

CAUTION

DO NOT ACTUATE ON THE REAR BRAKE LEVER AFTER REMOVING THE WHEEL, OTHERWISE
THE CALLIPER PLUNGER COULD GO OUT OF ITS SEAT, RESULTING IN BRAKE FLUID LEAK-
AGE.

•

Remove the snap ring (1).

BEFORE REMOVING THE PIN (2), CHECK THAT THE
SAFETY SPRING (3) IS CORRECTLY POSITIONED; WHEN
REFITTED, IT MUST POSITIONED IN THE SAME WAY.

Braking system

RSV4 R

BRAK SYS - 426

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 R

R&G LP0273 Fitting Instructions Manual preview
LP0273
Brand: R&G Pages: 22
R&G ECC0337R Fitting Instructions Manual preview
ECC0337R
Brand: R&G Pages: 8
Memphis Shades 2320-0039 Mounting Instructions preview
2320-0039
Brand: Memphis Shades Pages: 2
N-Com SPCOM00000091 Quick Start Manual preview
SPCOM00000091
Brand: N-Com Pages: 6
rizoma BS174 User Manual preview
BS174
Brand: rizoma Pages: 10
Triumph Bonneville T100 Owner'S Handbook Manual preview
Bonneville T100
Brand: Triumph Pages: 198
hepco & becker 5014550 00 05 Mounting Instructions preview
5014550 00 05
Brand: hepco & becker Pages: 4
Honda CBR150R Owner'S Manual preview
CBR150R
Brand: Honda Pages: 98
Yamaha XJ600SK Owner'S Manual preview
XJ600SK
Brand: Yamaha Pages: 110
DYNATEK DDK1-8 Installation Manual preview
DDK1-8
Brand: DYNATEK Pages: 12
N-Com B901-R User Instructions And Safety preview
B901-R
Brand: N-Com Pages: 36
hepco & becker 670.7501 Assembling Instructions preview
670.7501
Brand: hepco & becker Pages: 4
Gilera Nexus 250 i.e. Manual preview
Nexus 250 i.e.
Brand: Gilera Pages: 96
APRILIA Mojito 150 Manual preview
Mojito 150
Brand: APRILIA Pages: 128
APRILIA MX 50 Manual preview
MX 50
Brand: APRILIA Pages: 162
hepco & becker 7003534 00 01 Quick Start Manual preview
7003534 00 01
Brand: hepco & becker Pages: 2
KTM 250 SX-F US Owner'S Manual preview
250 SX-F US
Brand: KTM Pages: 112
KTM 2014 350 EXC-F SIX DAYS Owner'S Manual preview
2014 350 EXC-F SIX DAYS
Brand: KTM Pages: 136

Brands by name

Popular brands

Load more brands