APRILIA RSV4 R Service Station Manual Download Page 188

Page: 188 / 475

Throttle body

Function

Sends to the injection control unit the throttle position and activates the throttle according to the control

unit

Operation / Operating principle

All the unit internal components (potentiometer and electric motor) are contactless; therefore, no elec-

trical diagnosis is possible for the throttle body, but for the circuits connected to it only.

Level in wiring diagram:

Throttle check and throttle grip sensor (Demand)

Location:

•

on the vehicle: inside the filter box

•

connector: on the throttle body, in lower position, near the throttle motors

Pin out:

1. potentiometer signal 1

2. supply v 5V

3. throttle valve control (+)

4. potentiometer signal 2

5. throttle valve control (+)

6. ground connection

DIAGNOSIS INSTRUMENT:

PARAMETERS

Front cylinder throttle correction

•

Example value with key ON: 0.0°

•

Example value with engine on: 0.4°

The system, reading the intake pressure, tries to balance the intake pressures between the cylinders

of the rear bank (1-3) and of the front bank (2-4) working on the throttle position: an acceptable value

should be between -0.5 and + 0.5

Rear cylinder throttle correction

•

Example value with key ON: 0.0°

•

Example value with engine on: -0.2°

The system, reading the intake pressure, tries to balance the intake pressures between the cylinders

of the rear bank (1-3) and of the front bank (2-4) working on the throttle position: an acceptable value

should be between -0.5 and + 0.5

Front throttle Potentiometer 1 (degrees)

•

Example value with key ON: 7.8°

•

Example value with engine on: 1.4°

With key set to ON, the throttle is kept in position by the springs (around 5 -7°). After the engine starts

up at idle, the throttle is kept close to the mechanical minimum (above or equal to 0.5°). When the gear

Electrical system

RSV4 R

ELE SYS - 188

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands

APRILIA RSV4 R, Service Station Manual

Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands