manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 321 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 321

•

alternator;

•

water pump;

•

gearbox unit;

•

primary transmission shaft gear

•

both timing chains;

•

the chain sliders;

•

oil sump;

•

the gear selector pin spacer;

•

starter motor and intermediate gear;

•

countershaft.

See also

Magneto flywheel removal
Water pump
Disassembling the gearbox
Main

transmission gear removal

Front head removal
Rear head removal
Removing the oil sump
Removing the starter motor
Balancing countershaft removal

Crankcase opening

•

Position the engine with the heads fac-

ing upward, unscrew and remove the

screw (24).

RSV4 R

Engine

ENG - 321

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments