manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 154 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 154

Engine rpm sensor

Function

informs crankshaft position and speed to the Mar-

elli control unit

Operation / operating principle

inductive sensor: sinusoidal-type generated volt-

age; two teeth are missing on the flywheel for the

reference position

Level in wiring diagram:

Engine speed sensor

Location:

•

on the vehicle: on the clutch cover

•

connector: under the tank on the right

(3-ways black connector)

Electrical characteristics:

0.79 kohm at ambient temperature

Pin out:

1. negative signal

2. positive signal

3. shielding with ground connection

DIAGNOSIS INSTRUMENT:

 

PARAMETERS

Engine rpm:

 rpm

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSIS INSTRUMENT: STATUSES

Synchronised panel

•

No_under analysis_standby_Yes

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

CAUTION

IF THE ELECTRIC CIRCUIT IS INTERRUPTED OR SHORT-CIRCUITED, NO ERROR IS DIS-
PLAYED. CHECK THE ENGINE SPEED SENSOR CONNECTOR AND THE MARELLI CONTROL
UNIT CONNECTOR: IF NOT OK, RESTORE; IF OK, CHECK THE CORRECT ELECTRIC CHAR-
ACTERISTICS OF THE SENSOR: IF NOT OK, REPLACE THE SENSOR. IF OK, CHECK THAT
THERE IS CONTINUITY ON BOTH CABLES, SUPPLY INSULATION AND GROUND INSULATION.
CARRY OUT THE TESTS FROM THE SENSOR CONNECTOR TO THE SENSOR. IF NOT OK, RE-
STORE THE CABLE HARNESS/REPLACE THE SENSOR. IF OK, PERFORM THE TEST FROM PIN
9 AND 23 OF THE MARELLI CONTROL UNIT ENGINE CONNECTOR.

DIAGNOSIS INSTRUMENT: LOGIC ERRORS

Electrical system

RSV4 R

ELE SYS - 154

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments