manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 409 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 409

FLATTENED OR JAMMED CHAIN LINKS SHOULD BE LUBRICATED AND GOOD OPERATING
CONDITIONS RESTORED.

THE GEARING CHAIN HAS SEALING RINGS AMONG THE LINKS THAT KEEP THE GREASE
INSIDE.
ADJUST, LUBRICATE, WASH AND REPLACE THE CHAIN WITH UTMOST CAUTION.

CLEANING AND LUBRICATION

Do not wash the chain with water jets, steam jets, high-pressure water jets and highly flammable sol-

vents.

•

Wash the chain with fuel oil or kerosene. Maintenance operations should be more frequent

if there are signs of quick rust.

Lubricate the chain at the intervals specified on the routine maintenance table and whenever necessary.

•

Wash the chain, allow to dry and lubricate with spray grease for sealed chains.

Chain sliders

•

Place the vehicle on its OPTIONAL

rear service stand.

•

Check that the pad (1) is not worn or

damaged. Replace it with a new one if

it is.

•

Check the chain guide (2) for wear.

•

Unscrew and remove the two screws

from the left rider footpeg protection.

•

Remove the rear wheel.

RSV4 R

Chassis

CHAS - 409

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments