manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 213 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 213

•

position error.

Error cause

•

Position indicated by potentiometer does not correspond with position set by control unit.

Troubleshooting

•

Mechanically check the valve, its normal rotation (with cables disconnected from motor,

manually activate the cables and see movement regularity and check valve complete stroke

with correct operation of the return spring) and absence of foreign bodies which do not allow

its rotation: if not OK, restore; if OK, check valve and instrument panel connectors (special

attention to oxidation) and check cables resistance: if not OK, restore; if OK, always with

cables disconnected and key set to ON, check normal rotation of the electric motor and

replace motor (potentiometer does not work correctly).

DIAGNOSIS INSTRUMENT: ADJUSTABLE PARAMETERS

•

Acquire exhaust valve zero position.

NOTE: Motor is placed in a reference position to correctly search mechanical stop later.

•

Exhaust valve self-acquisition

NOTE: Search minimum and maximum mechanical stop.

The system consists of a throttle valve (1) with a return spring placed in the exhaust pipe. The valve is

closed via two cables actuated by an electric motor (2) which, in turn, is connected electrically to the

instrument panel. The operating logic and motor control are, however, resident in the Marelli injection

control unit, which dialogues with the instrument panel via the CAN.

The motor unit (2) consists of a potentiometer for position detection and a DC electric motor (2).

At key-ON, a valve (1) self-cleaning cycle is performed.

In the event of malfunction (electric or mechanical), the valve (1) may remain stuck in the closed position.

In the event of a CAN line malfunction, the valve (1) is returned to the open position.

In the event of removal or replacement of one or more system components (cables, valve or motor), a

calibration procedure is required.

RSV4 R

Electrical system

ELE SYS - 213

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments