manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 470 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 470

- Through the diagnosis tool, check that the last mapping version is present in the control unit/s and, if

required, program the control unit/s again: consult the technical service website to know about available

upgrades and details regarding the operation.

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE
IT IS FIRST USED SHORTENS BATTERY LIFE.

CAUTION

UPON INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE ONE, AND PERFORM THE REVERSE OPERATION UPON REMOVAL.

WARNING

THE BATTERY ELECTROLYTE IS POISONOUS AS IT MAY CAUSE SERIOUS BURNS. IT CON-
TAINS SULPHURIC ACID. AVOID CONTACT WITH YOUR EYES, SKIN AND CLOTHING.
IN CASE OF CONTACT WITH YOUR EYES OR SKIN, WASH WITH ABUNDANT WATER FOR AP-
PROX. 15 MIN. AND SEEK MEDICAL ATTENTION IMMEDIATELY.
IF ACCIDENTALLY SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR
VEGETABLE OIL. SEEK MEDICAL ATTENTION IMMEDIATELY.
BATTERIES PRODUCE EXPLOSIVE GASES; KEEP CLEAR OF NAKED FLAMES, SPARKS OR
CIGARETTES. VENTILATE THE AREA WHEN RECHARGING INDOORS. ALWAYS WEAR EYE
PROTECTION WHEN WORKING IN THE PROXIMITY OF BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

Levels check

- Hydraulic braking system fluid level

- Clutch system fluid level (if present)

- Gearbox oil level (if present)

- Transmission oil level (if present)

- Engine coolant level (if present)

- Engine oil level

- Mixer oil level (if present)

Road test

- Cold start

- Instrument panel operation

Pre-delivery

RSV4 R

PRE DE - 470

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments