APRILIA RSV4 R Service Station Manual Download Page 211

Page: 211 / 475

•

If potentiometer signal is above maximum threshold: voltage of the maximum end of stroke

position (open valve) outside the foreseen field has been detected. If potentiometer signal

is below maximum threshold: voltage of the minimum end of stroke position (closed valve)

outside the foreseen field has been detected. If time is excessive: excessive time for stop

search has been detected (possible mechanical problem of the valve, of the motor or cables

not connected). If research has not been carried out or wrong stroke: this symptom may be

caused when a new instrument panel is installed and the stop self-acquisition procedure is

not carried out or if the stop between minimum and maximum is too short or too long.

Troubleshooting

•

If potentiometer signal is above maximum threshold: during adjustment "Exhaust valve self-

acquisition", voltage of maximum opening end of stroke outside the foreseen field is

detected. Check correct tensioning of the two valve cables.

•

If potentiometer signal is below maximum threshold: during adjustment "Exhaust valve self-

acquisition", voltage of minimum opening end of stroke outside the foreseen field is detected.

Check correct tensioning of the two valve cables.

•

If time is excessive: check that the valve cables are in voltage: if they are not in voltage, fix

them; if they are OK, check that mechanical rotation of the exhaust valve is without friction

or deceleration: if they are not OK, restore normal valve rotation; if they are OK, check motor

electrical characteristics: if they are not OK, replace the motor; if they are OK, check valve

connector and instrument panel connector (with special attention to possible oxidation): if

they are not OK, restore; if they are OK, replace the electrical motor. Or also free cables.

•

If research has not been carried out or wrong stroke: adjust "Exhaust valve self-acquisition"

if the stop self-acquisition procedure has not been carried out after installation of new in-

strument panel. If the instrument panel is not new, check correct calibration of the cables

and if correct, check that there is not an obstacle for correct rotation of the valve.

Exhaust valve engine P0192

•

open circuit, thermal overload protection, shorted to negative, shorted to positive or short

circuit between both cables.

Error cause

•

If the circuit is open: too low current has been detected at PIN 36 - 37 of the instrument panel

connector. If thermal overload protection: instrument panel fault. If shorted to negative: volt-

age equal to zero has been detected. If shorted to positive or short circuit between both

cables: excessive voltage has been detected.

Troubleshooting

•

If the circuit is open: may occur due to loosen cables, therefore, make sure that cables are

tight: if not tight, fix them; if cables are OK, check valve connector and instrument panel

RSV4 R

Electrical system

ELE SYS - 211

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands

APRILIA RSV4 R, Service Station Manual

Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands