manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 293 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 293

020852Y

 

Crankshaft timing pin

Rear head

Removing camshafts

•

Remove the rear head cover and the clutch cover.

•

Move cylinder piston 1 (left rear piston) to the TDC;

•

Turn the crankshaft 450° (one complete turn + 90°) in the direction of motor rotation (direction

of travel).

•

Insert the pin from the clutch side into

the hole in the crankshaft.

NOTE

THE SPECIAL TOOL IS ONLY USED FOR IDENTIFYING
THE CORRECT CRANKSHAFT POSITION.
DO NOT USE IT FOR TIGHTENING OPERATIONS.

Specific tooling

020852Y

 

Crankshaft timing pin

See also

Head cover removal
Removing the

clutch cover

•

Fit the pin aligning the intake camshaft

with the hole in the U bolt.

•

If it was not possible before adjusting

the valve clearance, check the engine

timing.

Specific tooling

020851Y

 

Camshaft timing pin

RSV4 R

Engine

ENG - 293

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments