manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual

The APRILIA RSV4 R Service Station Manual is an essential tool for motorcycle enthusiasts. This comprehensive manual provides users with detailed instructions on all aspects of servicing and maintaining their RSV4 R. Download this manual for free at manualshive.com and keep your bike running smoothly for years to come.

Share
Download
background image

Variable geometry intake

(IF AVAILABLE)

Function

Extend or shorten the engine inlet ducts to in-

crease the inlet air quantity according to the engine

revs.

Operation / operating principle

The system consists of:

•

two inlet ducts for each manifold, which

may be joined (long ducts) or separa-

ted (short ducts);

•

a motor that, by means of an endless

screw, activates the upper part of the

inlet ducts;

•

a variable geometry control unit for

managing the system, interfaced with

the engine injection control unit.

At key-ON, the variable geometry control unit low-

ers the ducts (if still in the raised position). Subse-

quently, depending on the control voltage on PIN

2 from the injection control unit (0V down, 5V up),

the control unit drives the electric motor with the

relative polarity for raising or lowering the ducts.

The drive voltage delivered to the motor is deter-

mined in relation to battery voltage and the motor

is stopped once a given current limit is reached or

if the time-out period of 500 ms has elapsed.

Level in wiring diagram:

Variable geometry

Location:

•

on the vehicle: ducts and motor inside

the filter box, variable geometry control

unit on rear frame under the saddle,

right side.

•

variable geometry control unit connec-

tor: on the control unit.

RSV4 R

Electrical system

ELE SYS - 151

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 R

SRC B-TRK502-01-01-SL Quick Start Manual preview
B-TRK502-01-01-SL
Brand: SRC Pages: 5
Yamaha XJR1300(L) 99 Service Manual preview
XJR1300(L) 99
Brand: Yamaha Pages: 338
Yamaha TRACER MTT9K 2019 Owner'S Manual preview
TRACER MTT9K 2019
Brand: Yamaha Pages: 122
Yamaha TT-R125(N) 2000 Owner'S Service Manual preview
TT-R125(N) 2000
Brand: Yamaha Pages: 508
Yamaha TT-R125(R) 2002 Owner'S Service Manual preview
TT-R125(R) 2002
Brand: Yamaha Pages: 510
Yamaha TT-R125(V) Owner'S Service Manual preview
TT-R125(V)
Brand: Yamaha Pages: 610
Yamaha TT-R125(S) 2003 Owner'S Service Manual preview
TT-R125(S) 2003
Brand: Yamaha Pages: 610
Yamaha TT-R125(W) Owner'S Service Manual preview
TT-R125(W)
Brand: Yamaha Pages: 616
Yamaha TT-R110E 2021 Owner'S Manual preview
TT-R110E 2021
Brand: Yamaha Pages: 90
Arai QUANTUM-X Operation Instructions Manual preview
QUANTUM-X
Brand: Arai Pages: 12
SW-Motech SBL.07.565.100 Mounting Instructions preview
SBL.07.565.100
Brand: SW-Motech Pages: 2
SW-Motech HPS.11.258.900-01 Mounting Instructions preview
HPS.11.258.900-01
Brand: SW-Motech Pages: 2
SW-Motech TRT.00.787.32500/B Mounting Instructions preview
TRT.00.787.32500/B
Brand: SW-Motech Pages: 6
Kuberg CROSS Owner'S Manual preview
CROSS
Brand: Kuberg Pages: 16
Kuberg Freerider 2016 Owner'S Manual preview
Freerider 2016
Brand: Kuberg Pages: 32
Kuberg Ranger Owner'S Manual preview
Ranger
Brand: Kuberg Pages: 38
Vermont Castings 2008 Operator'S Manual preview
2008
Brand: Vermont Castings Pages: 31
Honda Gold Wing GL1100 Service Manual preview
Gold Wing GL1100
Brand: Honda Pages: 356

Brands by name

Popular brands

Load more brands