APRILIA RSV4 R Service Station Manual Download

Page: 359 / 475

After making any adjustment, wait for confirmation

that the position of the adjusted screw position is

now correct.

The procedure then continues with screws 2 and 4.

To ensure correct engine operation, one of the two screws of each throttle body must

always

be closed.

Motorcycles are factory set with screws 1 and 2 turned by half a turn and screws 3 and 4 closed.

RSV4 R

Power supply

P SUPP - 359

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands

APRILIA RSV4 R, Service Station Manual

Search results

Summary of Contents for RSV4 R

Reviews:

Related manuals for RSV4 R

Brands by name

Popular brands