SCREEN 5
INSTALLATIONS DATA: ALPHAVISION NG v1.1 -- date
IO01 IO02 IO03 IO04 IO05 IO06 IO07 IO08 IO09 IO10 IO11 CP DC
OK A 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK B 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK C 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK D 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK E 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK F 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK G 00 .. .. .. .. .. .. .. .. .. .. 000 00
OK H 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer A 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer B 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer C 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer D 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer E 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer F 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer G 00 .. .. .. .. .. .. .. .. .. .. 000 00
Buzzer H 00 .. .. .. .. .. .. .. .. .. .. 000 00
Attention
: In screen 5 you can program outputs to be activated when a section is OK, or ready to arm. The
OK outputs are only activated when all direct and 24 hour zones of the section are closed and when there are
no further technical complications that could stop the control panel from arming. The OK outputs can be
used when key switches are used, to show that the zones in the sections are closed and that the user can arm
the section(s) without any problems. In screen 6 you also program an output to be activated when all
sections are ready to arm, at “Totally OK”.
The
buzzer
output can be used to activate an external buzzer for each section during the entry and exit
delays. The buzzer output runs parallel to the internal buzzer of the keypads. The buzzer output is also
dependant on the programming in screen 8, at “buzzer during entrytime” and “buzzer during exit time”.
SCREEN 6
INSTALLATIONS DATA: ALPHAVISION NG v1.1 -- date
IO01 IO02 IO03 IO04 IO05 IO06 IO07 IO08 IO09 IO10 IO11 CP DC
Sabotage case 00 .. .. .. .. .. .. .. .. .. .. 000 00
Sabotage keyp 00 .. .. .. .. .. .. .. .. .. .. 000 00
Fail to comm 00 .. .. .. .. .. .. .. .. .. .. 000 00
Fail 230V/batt 00 .. .. .. .. .. .. .. .. .. .. 000 00
Doorbell outp 00 .. .. .. .. .. .. .. .. .. .. 000 00
Totally ARMED 00 .. .. .. .. .. .. .. .. .. .. 000 00
Totally OK 00 .. .. .. .. .. .. .. .. .. .. 000 00
Reset output 00 .. .. .. .. .. .. .. .. .. .. 000 00
*+# pressed 00 .. .. .. .. .. .. .. .. .. .. 000 00
not used 00 .. .. .. .. .. .. .. .. .. .. 000 00
not used 00 .. .. .. .. .. .. .. .. .. .. 000 00
RTC module 1 00 .. .. .. .. .. .. .. .. .. .. 000 00
RTC module 2 00 .. .. .. .. .. .. .. .. .. .. 000 00
RTC module 3 00 .. .. .. .. .. .. .. .. .. .. 000 00
RTC module 4 00 .. .. .. .. .. .. .. .. .. .. 000 00
Maintenance 00 .. .. .. .. .. .. .. .. .. .. 000 00
At
Tamper case
you can program the outputs that will be activated when the casing of the control panel or
one of the modules is opened. By using F27# “MAINTENANCE”, you can open the casings without
causing an alarm and activating the outputs.
At
Tamper keyp
you can program the outputs that will be activated when one of the keypads is opened, or
when the communication between the control panel and the keypads is cut off. By using F27#
“MAINTENANCE”, you can open the keypads without causing an alarm and activating the outputs.
AlphaVision NG installation manual Rev. 2.0 27-08-2003 Blz. 44/101
