Aimco AcraDyne Gen IV iAC, Operation Manual

Page: 54 / 68

54
AcraDyne Gen IV iAC Controller Manual
Low Angle Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Low Angle” output assignment will go active at the completion of a fastening that has a low angle results.
It will go inactive when the next fastening is started (the torque exceeds the threshold value) or a Job reset.
High Angle Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “High Angle” output assignment will go active at the completion of a fastening that has high angle results.
It will go inactive when the next fastening is started (the torque exceeds the threshold value) or a Job reset.
Fastening Complete Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Fastening Complete” output assignment will go active at the completion of a fastening. It will go inactive
when the next fastening is started (the torque exceeds the threshold value) or a Job reset.
In Cycle Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “In Cycle” output assignment will go active at the start of the fastening cycle (the torque exceeds the
threshold value). It will go inactive when the fastening cycle ends.
Fastening Aborted Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Fastening Aborted” output assignment will go active at the completion of a fastening that was aborted by the
system. It will go inactive when the next fastening is started (the torque exceeds the threshold value) or a Job reset.
Fastening Stopped Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Fastening Stopped” output assignment will go active at the completion of a fastening that was stopped by the
user. It will go inactive when the next fastening is started (the torque exceeds the threshold value) or a Job reset.
Batch Complete Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Batch Complete” output assignment will go active at the completion of a fastening that satisfies the
bolt count of a Job sequence. It will go inactive when the next fastening is started (the torque exceeds the
threshold value) or the job is reset.
Job Complete Supported Feature
Bus Element
Bit
0-32
Polarity
N.O./N.C.
Mode
Normal, Timed, Flash Time Width Offset
Input
Bus
Input
Element
Input
Bit
√ √ √ √ √
The “Job Complete” output assignment will go active at the completion of a fastening that satisfies all the
sequences. It will go inactive when the next fastening is started (the torque exceeds the threshold value) or the
job is reset.