Acom M47 User Manual Download Page 98

Page: 98 / 136

M47 User’s Guide - Page 98

When the Print Quality is Poor

When the print quality is poor, select the closest symptom from the following
table to rectify the problem.

If the print quality does not improve after carrying out the appropriate action,
contact service.

Symptom

Reason/Action

Printing is light.
(faded, blurred).

The paper is damp. Replace with paper from a new ream.

See page 37.

The drum/toner cartridge is defective/damaged or there
is no more toner inside the cartridge. Replace with a new
drum/toner cartridge.

See page 115.

The Toner Saving feature is on. Un-check the [Toner Saving]
check box on the [Graphics] tab of the printer driver.

See the Online Help for the printer driver

Levers on both sides of the fuser unit are raised. Open
cover B of this printer and push down the levers at both
ends of the fuser unit.

Black spots
or streaks are
printed.

The drum/toner cartridge is defective or damaged. Replace
with a new drum/toner cartridge.

See page 115.

Toner appears
at equal
intervals.

The paper feed rout contains excess toner. Print a few
pages to remove the excess toner.

The drum/toner cartridge is defective or damaged. Replace
with a new drum/toner cartridge. See page 115.

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands