Acom M47 User Manual Download Page 60

Page: 60 / 136

M47 User’s Guide - Page 60

Admin\ Job Accounting Menu

Default settings are in

bold face

type.

SubMenu

Available Settings

Enabled

Yes,

Print Info

Execute

Admin\ Change Password Menu

Used to change the Operator Panel Password that is used to gain access to the
“Admin Setup” menus. For more information, see page 50.

Admin\ Maintenance Menu

Default settings are in

bold face

type.

Submenus

Available Settings Description

Menu Reset

Execute

Restore the panel settings to Factory
Default.

Save Menu

Execute

Saves the current menu setup for recall
at a later time.

Restore Menu

Execute

Restores the saved Menu setting

Panel Security

Enable,

Disable

If enabled, all configuration changes
require the password.

USB Drive

Enable

, Disable

If enabled, gives the printer the ability
to read and print files from a connected
USB drive.

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands