Acom M47 User Manual Download Page 43

Page: 43 / 136

M47 User’s Guide - Page 43

USB Drive Menu

Note

•

This Menu item will only appear if a USB Flash drive is installed in the
Host USB connector on the operator panel.

The [

USB Drive

] menu allows the user to print a selected file from the installed

USB Flash Drive. The file selected for printing must be one of the following
formats:

■

Supported PDF

■

PCL5, PCL6, FX80 or PostScript

■

Generic text (such as a .txt file)

Size of PDF files to be printed is limited by available space in standard user flash
memory unless a Compact Flash or Hard Disk option is installed.

To print a PDF file form a USB flash drive, see page 61.

Print Jobs Menu

This menu is used to access print jobs stored in the printer. For information on
printing stored jobs, see page 63.

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands