Acom M47 User Manual Download Page 132

Page: 132 / 136

M47 User’s Guide - Page 132

When Moving the Printer

WaRNING

•

The printer, without the optional accessories, paper trays, consumables
and paper, weighs 41.4 lb. (18.8 kg).

•

When lifting the printer, be sure to observe the following points, failure to
do so may cause the printer to fall and result in injuries.

•

2 persons, one facing the front of the printer (control panel) and the
other facing the back, should firmly grip the recessed areas on the
bottom part of both sides of the printer. Never try to lift the printer by
gripping any other areas.

•

Bend your knees to avoid possible injuries to your back.

•

Do not tilt the printer more than 10 degrees.

WaRNING

•

If the optional duplex unit or optional A4 universal tray is installed,
uninstall it before moving the printer.

•

If these are not fixed securely to the printer, they may fall to the ground
and cause injuries.

1. Press the power switch of this printer to the <O> position to switch the

power off.

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands