Acom M47 User Manual Download Page 44

Page: 44 / 136

M47 User’s Guide - Page 44

Configuration\ Page Counts Menu

Provides access to certain counters inside the printer.

Submenus

Example

Resettable?

Usage Counter

123456

Yes

Page Counter

123456

Toner Page Count

123456

Yes

Fuser Count

123456

Yes
Note: Images larger than either A4 or
Letter are counted as 2 images.

Configuration\ Supplies Life Menu

Provides access to the printer supply levels.

Submenus

Available Settings

Tray1 Level

OK, Low, Empty

Tray2 Level

OK, Low, Empty

Tray3 Level

OK, Low, Empty

Tray4 Level

OK, Low, Empty

Toner

0% to 100% (percentage of toner remaining.)

Configuration\ Network Menu

For setting printer network parameters.

■

Printer Name

■

IP Address

■

Subnet Mask

■

Gateway Address

■

Network Address

■

Network Version

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands