Acom M47 User Manual Download Page 37

Page: 37 / 136

M47 User’s Guide - Page 37

Unusable Media

CautIoN

•

Using the following types of media might cause paper jams, malfunctions
or damage to the printer. Do not use them.

■

Fuji Xerox full-color transparencies (example: V556, V558, V302)

■

Paper exclusively for ink-jet printer use

■

Paper that is too thick or thin

■

Paper that has been printed on before (including color printing)

■

Wrinkled, folded or torn paper

■

Wet paper

■

Curled paper

■

Paper with static electricity

■

Adhesive paper

■

Paper with special coatings

■

Treated colored paper

■

Paper using ink that will run at a temperature of 302°F (150°C).

■

Thermal paper

■

Carbon paper

■

Paper with staples, paper clips, ribbons or tape

■

Paper with rough surfaces such as pulp paper or fibrous paper

■

If acid paper is used, the characters might appear fuzzy. Replace it with
alkaline paper.

■

Labels that do not fully cover the adhesive backing

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands