Acom M47 User Manual Download Page 112

Page: 112 / 136

M47 User’s Guide - Page 112

Routine Maintenance

Replacing the Drum/Toner Cartridge

The drum/toner cartridge includes the toner and the photosensitive drum. When
it is about time to replace the drum/toner cartridge, the following message will
appear on the control panel.

Ready to print
Repl. Drum/Toner

After this message displays, you can continue to print about 100 more sheets.
Make sure you have a new drum/toner cartridge on hand.

When the following message displays, printing stops and you must replace the
drum/toner cartridge.

Replace Drum/
Toner Cartridge

Note

•

If you continue to print with a worn-out drum/toner cartridge, it may affect
the functions of this printer, such as the print quality.

•

You can set whether to stop printing when the drum/toner cartridge is due
for replacement.

Summary of Contents for M47









































































































































Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands

Acom M47, User Manual

Search results

Summary of Contents for M47

Reviews:

Related manuals for M47

Brands by name

Popular brands