YASKAWA CPU 013C Скачать руководство пользователя страница 69

Страница: 69 / 263

Phase offset
–

Enter the delay time in ms for current execution for the watch dog interrupt. This

should be performed if several watchdog interrupts are enabled.

–

Phase offset allows to distribute processing time for watchdog interrupts across

the cycle.

Process image partition
–

This parameter is not supported.

Report cause of STOP
–

Activate this parameter, if the CPU should report the cause of STOP to PG

respectively OP on transition to STOP.

Number of messages in the diagnostics buffer
–

This parameter is ignored. The CPU always has a diagnostics buffer (circular

buffer) for 100 diagnostics messages.

Synchronization type
–

Here you specify whether clock should synchronize other clocks or not.

–

as slave: The clock is synchronized by another clock.

–

as master: The clock synchronizes other clocks as master.

–

none: There is no synchronization

Time interval
–

Time intervals within which the synchronization is to be carried out.

Correction factor
–

Lose or gain in the clock time may be compensated within a 24 hour period by

means of the correction factor in ms.

–

If the clock is 1s slow after 24 hours, you have to specify a correction factor of

"+1000" ms.

Level of protection
–

Here 1 of 3 protection levels may be set to protect the CPU from unauthorized

access.

–

Protection level 1 (default setting):

No password adjustable, no restrictions

–

Protection level 2 with password:

Authorized users: read and write access
Unauthorized user: read access only

–

Protection level 3:

Authorized users: read and write access
Unauthorized user: no read and write access

4.7.3 Parameter for MPI/DP

The properties dialog of the MPI(PtP) interface X3 is opened via a double click to the sub

module MPI/DP

To switch the interface X3 MPI(PtP) to PROFIBUS functionality you have

to activate the according bus functionality by means of a VSC storage

media from VIPA. By plugging the VSC storage card and then an overall

reset the according functionality is activated.

Chapter 4.15 ‘Deploy-

ment storage media - VSD, VSC’ on page 83

Diagnostics/Clock

Protection

VIPA System SLIO

Deployment CPU 013-CCF0R00

Setting standard CPU parameters > Parameter for MPI/DP

HB300 | CPU | 013-CCF0R00 | en | 16-40

Содержание CPU 013C








































































































































































































































































Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды

YASKAWA CPU 013C, Руководство пользователя

Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды