YASKAWA CPU 013C Скачать руководство пользователя страница 227

Страница: 227 / 263

So that you may the according Ethernet interface, you have to assign IP address parame-

ters by means of the "initialization".

Chapter 10.3 ‘TIA Portal - Hardware configuration -

Ethernet PG/OP channel’ on page 222

Please consider to use the same IP address data in your project for the CP 343-1.

For the transfer, connect, if not already done, the appropriate Ethernet jack to your

Ethernet.

Open your project with the Siemens TIA Portal.

Click in the

Project tree

Online access

and choose here by a double-click your

network card, which is connected to the Ethernet PG/OP interface.

Select in the

Project tree

your CPU and click at [Go online].

Set the access path by selecting "PN/IE" as type of interface, your network card and

the according subnet. Then a net scan is established and the corresponding station

is listed.

Establish with [Connect] a connection.

Click to

‘Online

Download to device’

The according block is compiled and by a request transferred to the target

device. Provided that no new hardware configuration is transferred to the CPU,

the entered Ethernet connection is permanently stored in the project as transfer

channel.

10.5.3

Transfer via memory card

The memory card serves as external storage medium. There may be stored several proj-

ects and sub-directories on a memory card. Please regard that your current project is

stored in the root directory and has one of the following file names:

S7PROG.WLD

AUTOLOAD.WLD

Start the Siemens TIA Portal with your project.

Create a wld file with

‘Project

Memory card file

New’

The wld file is shown in the

Project tree

at "SIMATIC Card Reader" as "Memory

card file".

Copy the blocks from the

Program blocks

to the wld file. Here the hardware configu-

ration data are automatically copied to the wld file as "System data".

Copy the wld file at a suited memory card. Plug this into your CPU and start it

again.

The transfer of the application program from the memory card into the CPU

takes place depending on the file name after an overall reset or PowerON.

S7PROG.WLD

is read from the memory card after overall reset.

AUTOLOAD.WLD

is read from the memory card after PowerON.

The blinking of the SD LED of the CPU marks the active transfer. Please regard

that your user memory serves for enough space for your user program, other-

wise your user program is not completely loaded and the SF LED gets on.

Initialization

Transfer

Proceeding

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Project transfer > Transfer via memory card

HB300 | CPU | 013-CCF0R00 | en | 16-40

227

Содержание CPU 013C








































































































































































































































































Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды

YASKAWA CPU 013C, Руководство пользователя

Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды