YASKAWA CPU 013C Скачать руководство пользователя страница 17

Страница: 17 / 263

Dimensions in mm

2.4 Mounting

2.4.1 Mounting CPU 01xC

There are locking lever at the top side of the CPU. For mounting and demounting these

locking lever are to be turned upwards until these engage. Place the CPU at the

mounting rail. The CPU is fixed to the mounting rail by pushing downward the locking

levers. The CPU is directly mounted at a mounting rail. Up to 64 modules may be

mounted. The electronic and power section supply are connected via the backplane bus.

Please consider here that the sum current of the electronic power supply does not

exceed the maximum value of 1A. By means of the power module 007-1AB10 the current

of the electronic power supply may be expanded accordingly.

Dimension periphery

module

Dimensions electronic

module

VIPA System SLIO

Basics and mounting

Mounting > Mounting CPU 01xC

HB300 | CPU | 013-CCF0R00 | en | 16-40

Содержание CPU 013C








































































































































































































































































Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды

YASKAWA CPU 013C, Руководство пользователя

Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды