YASKAWA CPU 013C Скачать руководство пользователя страница 21

Страница: 21 / 263

By means of a screwdriver there is the possibility to remove the connectors e.g. for

module exchange with a fix wiring. For this each connector has a release lever centrally

on its top side. Unlocking takes place by the following proceeding:

Remove connector:

Push your screwdriver horizontally into the slot between connector and release

lever, until it stops.

Push the screwdriver down:

The connector is unlocked and can be removed by turning downwards.

CAUTION!

Via wrong operation such as pressing, the screwdriver upward

the release lever may be damaged.

Plug connector:

The connector is plugged by setting it at the bottom line and engage with a with a

slight twist upwards into the release lever.

(1) DC 24V for electronic section supply of the CPU, the internal I/Os and SLIO bus

(2) DC 24V for power section supply integrated I/Os

(3) DC 24V for power section supply SLIO bus

The electronic power section supply is internally protected against higher

voltage by fuse. The fuse is located inside the CPU and can not be

changed by the user.

Remove connectors

(module replacement)

Standard wiring

VIPA System SLIO

Basics and mounting

Wiring > Wiring CPU 01xC

HB300 | CPU | 013-CCF0R00 | en | 16-40

Содержание CPU 013C








































































































































































































































































Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды

YASKAWA CPU 013C, Руководство пользователя

Результаты поиска

Содержание CPU 013C

Отзывы:

Похожие инструкции для CPU 013C

Бренды по названию

Популярные бренды