Yamaha F300 Скачать руководство пользователя | Manualshive

Страница: 87 / 124

background image

Operation

81

4.

Set the tilt support lever to support the
engine.

WARNING! After tilting the

outboard motor, be sure to support it
with the tilt support knob or tilt sup-
port lever. Otherwise the outboard
motor could fall back down suddenly
if oil in the power trim and tilt unit or
in the power tilt unit loses pressure.

[EWM00262]

NOTICE:

Do not use the tilt

support lever or knob when trailering
the boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 85.

[ECM01641]

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Be sure to retract

the trim rods completely during
mooring. This protects the rods from
marine growth and corrosion which
could damage the power trim and tilt
mechanism.

[ECM00251]

EMU35513

Procedure for tilting down (power
trim and tilt models)

1.

The main switch must be “

” (on) for

the power trim and tilt switch on the dig-
ital electronic control to operate.

2.

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

3.

Release the tilt support lever.

UP

ZMU05839

ZMU05824

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
85
86
87
88
89
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: Gigabyte Страницы: 46

Бренд: Abit Страницы: 48

Бренд: FAAC Страницы: 8

Бренд: Texas Instruments Страницы: 38

Бренд: DTK Страницы: 50

Бренд: Renesas Страницы: 20

Бренд: Freescale Semiconductor Страницы: 4

WAFER-CV-N26001

Бренд: IEI Technology Страницы: 135

PX845EV1 Series

Бренд: Albatron Страницы: 56

Бренд: JETWAY Страницы: 43

Бренд: ASROCK Страницы: 95

Бренд: Supermicro Страницы: 91

Бренд: Texas Instruments Страницы: 54

Бренд: Ublox Страницы: 18

Бренд: JETWAY Страницы: 48

Бренд: Gigabyte Страницы: 70

Бренд: ASROCK Страницы: 244

Бренд: California Eastern Laboratories Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды