Yamaha F300 страница 104 Скачать руководство пользователя | Manualshive

Страница: 104 / 124

background image

Maintenance

98

EMU30671

Installing propeller

EMU29243

Spline models

WARNING

EWM00770

On counter rotation models, be sure to
use a propeller intended for counter-
clockwise rotation. These propellers are
identified with the letter “L” after the size
indication on the propeller. Otherwise the
boat could move in the opposite direction

from that expected.

NOTICE

ECM00500

Be sure to use a new cotter pin and bend
the ends over securely. Otherwise the
propeller could come off during opera-

tion and be lost.

1.

Apply Yamaha marine grease or a cor-
rosion resistant grease to the propeller
shaft.

2.

Install the thrust washer and propeller
on the propeller shaft.

NOTICE:

Be sure

to install the thrust washer before in-
stalling the propeller, otherwise the
lower case and propeller boss could
be damaged.

[ECM01880]

3.

Install the spacer and washer. Tighten
the propeller nut to the specified torque.

4.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NO-

TICE:

Do not reuse the cotter pin in-

stalled. Otherwise the propeller can
come off during operation.

[ECM01890]

TIP:

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to
align it with the hole.

EMU31913

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-

ly falls.

1.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the
gear case.

3.

Remove the cooling water inlet covers
on both sides of the gear case. Be care-
ful not to lose the bolt and nut.

4.

Remove the gear oil drain screw and
gasket. The screw is magnetic so a
small quantity of metal particles on the
end of the screw is normal. Simply re-
move them.

NOTICE:

If there is an ex-

Propeller nut tightening torque:

55.0 Nm (5.61 kgf-m, 40.6 ft-lb)

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
102
103
104
105
106
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: M5Stack Страницы: 16

Бренд: SOLTEK Страницы: 49

Бренд: JETWAY Страницы: 46

Бренд: Biostar Страницы: 27

Бренд: DFI Страницы: 8

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Бренд: A-Trend Страницы: 60

Motherboard DJ800

Бренд: IWILL Страницы: 52

Бренд: Texas Instruments Страницы: 21

SUPER P4DPL-8GM

Бренд: Supero Страницы: 86

Бренд: Intersil Страницы: 26

DQ963FX - Desktop Board Motherboard

Бренд: Intel Страницы: 72

Бренд: Gigabyte Страницы: 96

Бренд: Gigabyte Страницы: 52

Бренд: Micrel Страницы: 10

Бренд: ASROCK Страницы: 244

Бренд: Ublox Страницы: 22

Бренд: Cebekit Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды