Yamaha F300 страница 115 Скачать руководство пользователя | Manualshive

Страница: 115 / 124

background image

Trouble Recovery

109

EMU35400

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt because of a dis-
charged battery or a failure with the power
trim and tilt unit, consult your Yamaha deal-
er.

EMU35073

Water separator-alert indicator blinks
while cruising

WARNING

EWM01500

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion

hazard.

If the water separator-alert indicator on the
Command Link tachometer blinks, perform
the following procedure.

1.

Stop the engine.

2.

Remove the top cowling.

3.

Disconnect the lead from the holder.

4.

Disconnect the water detection switch
coupler from the holder.

6. Shift actuator fuse (15 A)
7. Electric throttle valve fuse (10 A)
8. Engine main fuse (60 A)
9. Isolator fuse (60 A)

1. Water separator-alert indicator

ZMU05893

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
113
114
115
116
117
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: Gigabyte Страницы: 125

Бренд: National Semiconductor Страницы: 32

MS-6191 Micro ATX IR2

Бренд: MSI Страницы: 86

BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard

Бренд: Intel Страницы: 88

Бренд: ECS Страницы: 93

Бренд: Texas Instruments Страницы: 13

Бренд: IEI Technology Страницы: 160

Бренд: Seanix Страницы: 49

Бренд: Erreka Страницы: 4

Бренд: MATSONIC Страницы: 39

Бренд: MSI Страницы: 126

Бренд: MSI Страницы: 87

Бренд: Texas Instruments Страницы: 20

Бренд: JETWAY Страницы: 51

Бренд: TYAN Страницы: 67

Бренд: TYAN Страницы: 66

Бренд: ECS Страницы: 60

Бренд: Texas Instruments Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды