Yamaha F300 страница 51 Скачать руководство пользователя | Manualshive

Страница: 51 / 124

background image

Instruments and indicators

45

engine damage will occur.

●

Do not continue to operate the engine if
a alert device has activated. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

EMU36150

Water separator alert

This indicator will blink if water has accumu-
lated in the water separator (fuel filter) while
cruising. In such an event, stop the engine
immediately and see page 107 of this manu-
al to drain the water from the fuel filter. Get
back to the port soon and consult a Yamaha
dealer immediately.

NOTICE

ECM00910

Gasoline mixed with water could cause

damage to the engine.

EMU36160

Engine trouble alert

This indicator will blink if the engine malfunc-
tions while cruising. Get back to the port
soon and consult a Yamaha dealer immedi-
ately.

NOTICE

ECM00920

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer

immediately.

EMU36170

Low battery voltage-alert

If the battery voltage drops, the low battery
voltage-alert indicator and the battery volt-
age value will start to blink. Get back to the
port soon if the low battery voltage-alert de-
vice has activated. For charging the battery,
consult your Yamaha dealer.

ZMU05423

ZMU05424

ZMU05425

ZMU05426

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
49
50
51
52
53
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Industrial NUC-J6412

Бренд: ASROCK Страницы: 2

MYC-C8MMQ6-8E2D-160-I

Бренд: MYiR Страницы: 50

Бренд: Intertec Components Страницы: 3

SPC572LADPT100S

Бренд: ST Страницы: 29

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: ASROCK Страницы: 114

Бренд: Intel Страницы: 78

Бренд: ST Страницы: 82

Бренд: Evinrude Страницы: 76

880GM-LE - V1.0

Бренд: ASROCK Страницы: 60

Бренд: JETWAY Страницы: 41

Бренд: PC Partner Страницы: 20

Бренд: Gigabyte Страницы: 38

Бренд: Liantec Страницы: 4

Бренд: MSI Страницы: 87

Бренд: Fastrax Страницы: 12

Бренд: Supero Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды