Yamaha F300 Скачать руководство пользователя

Страница: 46 / 124

Components

When installing the cowling, align the 3 posi-
tions of the grommets to fit the cowling in the
rubber seal.

When installing the cowling, check to be sure
it fits properly in the rubber seal.
Be sure to check that the gap between the

top cowling and the bottom cowling is even
all around the cowling. If the top cowling is
loose or the gap is not even, reinstall the
cowling.

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

TIP:

For details on usage, see page 86.

EMU33462

Fuel filter/Water separator

This engine has a combination fuel filter/wa-
ter separator and associated alert system. If
water separated from the fuel exceeds a
specific volume, the alert device of Com-
mand Link Tachometer will activate.

ZMU05852

ZMU05853

ZMU05934

1. Flushing device

ZMU05825

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды