Yamaha F300 Скачать руководство пользователя

Страница: 107 / 124

Maintenance

101

battery manufacturer’s instructions.

NOTICE

ECM01920

A poorly maintained battery will quickly

deteriorate.

Check the electrolyte level.

Check the battery’s charge. If your boat
is equipped with the digital speedome-
ter, the voltmeter and low battery alert
functions will help you monitor the bat-
tery’s charge. If the battery needs charg-
ing, consult your Yamaha dealer.

Check the battery connections. They
should be clean, secure, and covered by
an insulating cover.

WARNING! Bad

connections can produce shorting or
arcing and cause an explosion.

[EWM01910]

EMU35493

Connecting the battery

WARNING

EWM00570

Mount the battery holder securely in a
dry, well-ventilated, vibration-free loca-
tion in the boat. Install a fully charged bat-

tery in the holder.

NOTICE

ECM01123

Reversal of the battery cables will dam-

age the electrical parts.

Make sure the main switch (on applica-
ble models) is “

” (off) before working

on the battery.

Connect the red battery cable to the
POSITIVE (+) terminal first. Then con-
nect the black battery cable to the NEG-
ATIVE (-) terminal.

The electrical contacts of the battery and
cables must be clean and properly con-
nected, or the battery will not start the
engine.

Connecting an accessory battery (optional)
1.

If connecting an accessory battery, con-
sult your Yamaha dealer about correct
wiring. For the fuse size, see ABYC (E-
11).

1. Red cable
2. Black cable
3. Battery

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды