Yamaha F300 страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 124

background image

Specifications and requirements

15

LF300TR XL
LF350TR XL

Fuel and oil:

Recommended fuel:

F300TR Regular unleaded gasoline
F350TR Premium unleaded gasoline
LF300TR Regular unleaded gasoline
LF350TR Premium unleaded
gasoline

Min. pump octane:

F300TR 85
F350TR 89
LF300TR 85
LF350TR 89

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil group 1*:

SAE 10W-30/10W-40/20W-40/
5W-30
API SE/SF/SG/SH/SJ/SL
FC-W rated 4-stroke 10W-30,
10W-40, 20W-40, 5W-30

Recommended engine oil group 2*:

SAE 15W-40/20W-50
API SH/SJ/SL

Lubrication:

Wet sump

Engine oil quantity without replacement of
oil filter (Oil pan capacity):

7.8 L (8.24 US qt, 6.86 Imp.qt)

Engine oil quantity with replacement of oil
filter (Oil pan capacity):

8.0 L (8.46 US qt, 7.04 Imp.qt)

Amount of adding engine oil (at Periodic
maintenance) Excluding oil filter:

6.3 L (6.66 US qt, 5.54 Imp.qt)

Amount of adding engine oil (at Periodic
maintenance) Including oil filter:

6.5 L (6.87 US qt, 5.72 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE 90 or 80W-90,

API GL-5

Gear oil quantity:

F300TR 1.520 L
(1.607 US qt, 1.338 Imp.qt)
F350TR 1.520 L
(1.607 US qt, 1.338 Imp.qt)
LF300TR 1.310 L
(1.385 US qt, 1.153 Imp.qt)
LF350TR 1.310 L
(1.385 US qt, 1.153 Imp.qt)

Tightening torque for engine:

Spark plug:

28.0 Nm (2.86 kgf-m, 20.7 ft-lb)

Propeller nut:

55.0 Nm (5.61 kgf-m, 40.6 ft-lb)

Engine oil drain bolt:

28.0 Nm (2.86 kgf-m, 20.7 ft-lb)

Engine oil filter:

18.0 Nm (1.84 kgf-m, 13.3 ft-lb)

EMU33553

Installation requirements

EMU33563

Boat horsepower rating

WARNING

EWM01560

Overpowering a boat can cause severe

instability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your mo-
tor(s) does not exceed the boats maximum
horsepower rating. See the boat’s capacity
plate or contact the manufacturer.

EMU33571

Mounting motor

WARNING

EWM01570

●

Improper mounting of the outboard mo-
tor could result in hazardous condi-
tions such as poor handling, loss of
control, or fire hazards.

●

Because the motor is very heavy, spe-

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
19
20
21
22
23
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: Abit Страницы: 120

Бренд: Acconeer Страницы: 14

Бренд: Alcad Страницы: 98

Analog Devices DC2605A

Бренд: Linear Страницы: 16

Бренд: Advantech Страницы: 118

Spacewalker AK32

Бренд: Shuttle Страницы: 89

Бренд: DFI Страницы: 62

Бренд: Xilinx Страницы: 70

Бренд: Alpha Data Страницы: 40

WizFi360-EVB-Pico

Бренд: Wiznet Страницы: 29

Бренд: Gigabyte Страницы: 104

Бренд: Fastfame Страницы: 41

Бренд: Honda Страницы: 152

Бренд: DFI Страницы: 44

Бренд: IEI Technology Страницы: 162

Бренд: ECS Страницы: 61

MBD-X11SDV-4C-TP8F-B

Бренд: Supermicro Страницы: 123

Бренд: EVGA Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды