Yamaha F300 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 124

background image

Specifications and requirements

16

cial equipment and training is required

to mount it safely.

Your dealer or other person experienced in
proper rigging should mount the motor using
correct equipment and complete rigging in-
structions. For further information, see page
52.

EMU34952

Digital electronic control

requirements

The digital electronic control be equipped
with a start-in-gear protection device(s). This
device prevents the engine from starting un-
less it is in neutral.

WARNING

EWM01580

●

If the engine starts in gear, the boat can
move suddenly and unexpectedly, pos-
sibly causing a collision or throwing
passengers overboard.

●

If the engine ever starts in gear, the
start-in-gear protection device is not
working correctly and you should dis-
continue using the outboard. Contact

your Yamaha dealer.

This digital electronic control unit is only
available for the outboard motor which you
have purchased.
Prior to use of the digital electronic control
unit, set it in order to operate your outboard
motor only. Otherwise, it will not be possible
to operate the outboard motor.
Perform setting of the outboard motor and
the digital electronic control unit in the follow-
ing cases.

●

If a used outboard motor is installed

●

If the digital electronic control unit is re-
placed

●

If the ECM (Electronic control module) of
the used outboard motor is replaced

●

If the ECM (Electronic control module) of
the digital electronic control unit is re-
placed

Consult your Yamaha dealer for setting.

EMU25694

Battery requirements

EMU25713

Specifications of Battery

Use a fully charged battery that meets the
following specifications. The engine cannot
be started if battery voltage is too low.

NOTICE

ECM01061

Do not use a battery that does not meet
the specified capacity. If a battery that
does not meet specifications is used, the
electric system could perform poorly or
be overloaded, causing electric system

damage.

EMU36290

Mounting battery

Mount the battery holder securely in a dry,
well-ventilated, vibration-free location in the
boat.

WARNING! Do not put flammable

items, or loose heavy or metal objects in
the same compartment as the battery.
Fire, explosion or sparks could result.

[EWM01820]

EMU36300

Multiple batteries

To connect multiple batteries, such as for
multiple engine configurations or for an ac-

Minimum cold cranking amps
(CCA/SAE):

700.0 A

Minimum marine cranking amps
(MCA/ABYC):

900.0 A

Minimum reserve capacity (RC/SAE):

170 minutes

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
20
21
22
23
24
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

ASC Bridge Board

Бренд: Lattice Semiconductor Страницы: 25

Бренд: SOYO Страницы: 95

Advanced Socket 370

Бренд: BCM Advanced Research Страницы: 38

S1V30080 Series

Бренд: Seiko Epson Страницы: 10

Бренд: Texas Instruments Страницы: 21

AR0832MBSC25SUFAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Бренд: ECS Страницы: 66

Бренд: ASROCK Страницы: 2

Бренд: AIC Страницы: 58

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Бренд: e2v Страницы: 39

Бренд: Gigabyte Страницы: 120

STEVAL-IHM011V1

Бренд: ST Страницы: 27

Бренд: CDI Страницы: 4

Бренд: AOpen Страницы: 8

Бренд: Biostar Страницы: 36

Бренд: DFI Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды