manualshive.com logo in svg

Yamaha F300, Руководство пользователя

Поделиться
Скачать
Yamaha F300 Скачать руководство пользователя страница 66

 

Operation

 

60

 

7.

Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.

8.

Tilt the outboard motor down. Check
that the tilt rod and trim rods operate
smoothly.

 

EMU36581

 

Battery

 

Check that the battery is in good condition,
and fully charged. Check that the battery
connections are clean, secure and covered
by insulating covers. The electrical contacts
of the battery and cables must be clean and
properly connected or the battery will not
start the engine.
Refer to the battery manufacturer’s instruc-
tions for checks for your particular battery.

 

EMU30022

 

Filling fuel

WARNING

 

EWM01830 

 

●

 

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

 

●

 

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your

doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,

 

change your clothes.

 

1.

Stop the engine.

2.

Be sure you are in a well-ventilated out-
door area, either securely moored or
trailered.

3.

Make sure no one is in the boat.

4.

Do not smoke and keep away from
sparks, flames, static electric discharge,
or other sources of ignition.

5.

If you use a portable container to store
and dispense fuel, only use a locally ap-
proved GASOLINE container.

6.

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electrostatic
sparks.

7.

Fill the fuel tank, but do not overfill. Fuel
can expand and overflow if the tempera-
ture increases.

8.

Tighten the filler cap securely.

9.

Wipe up any spilled gasoline immediate-
ly with dry rags. Dispose rags properly.
According to local laws or regulations.

 

EMU27451

 

Operating engine

 

EMU31811

 

Priming fuel system

 

1.

If there is a fuel joint or a fuel cock on the
boat, firmly connect the fuel line to the
joint or open the fuel cock.

2.

Squeeze the primer pump, with the ar-
row pointing up, until you feel it become
firm.

ZMU05855

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды