manualshive.com logo in svg

Yamaha F300, Руководство пользователя

Поделиться
Скачать
Yamaha F300 Скачать руководство пользователя страница 72

 

Operation

 

66

TIP:

 

The main station can start and stop the en-
gine. However, it cannot operate the digital
electronic control.

 

EMU36510

 

Checks after starting engine

 

EMU36520

 

Cooling water

 

Check for a steady flow of water from the
cooling water pilot hole. A continuous flow of
water from the pilot hole shows that the wa-
ter pump is pumping water through the cool-
ing passages. If the cooling passages are
frozen, it may take a while for water to start
flowing out of the pilot hole.

NOTICE

 

ECM01810 

 

If water is not flowing out of the pilot hole
at all times while the engine is running,
overheating and serious damage could
occur. Stop the engine and check wheth-

er the cooling water inlet on the lower
case or the cooling water pilot hole is
blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-

 

rected.

 

Check that no water leaks from the joints be-
tween the exhaust cover, cylinder head, and
body cylinder.

 

EMU27670

 

Warming up engine

 

EMU35264

 

Electric start models

 

After the engine has started, warm the en-
gine up until the engine speed settles at
idling speed.

 

EMU36530

 

Checks after engine warm-up

 

EMU36540

 

Shifting

 

While tightly moored, and without applying
throttle, confirm that the engine shifts
smoothly into forward and reverse, and back
to neutral.

 

EMU31721

 

Stop switches

 

●

 

Confirm that turning the main switch to the
“

” (off) position stops the engine.

 

●

 

Confirm that removing the clip from the en-
gine shut-off switch stops the engine.

 

●

 

Confirm that the engine cannot be started
with the clip removed from the engine

ZMU05984

ZMU05985

ZMU05848

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды