manualshive.com logo in svg

Yamaha F300, Руководство пользователя

Поделиться
Скачать
Yamaha F300 Скачать руководство пользователя страница 53

 

Instruments and indicators

 

47

 

EMU31621

 

Command link multifunction 

speedometers

 

The speedometer unit shows the boat speed
and has functions of fuel meter and system
voltage display. The chosen display is se-
lected by using the “

” (set) and “

”

(mode) buttons as described in this section.
In addition, the speedometer can show the
desired unit of measurement such as km/ h,
mph, or knots. If optional sensors are con-
nected to the unit, trip display, water surface
temperature display, depth display, and
clock will also be available. For the optional
sensors, consult your Yamaha dealer.
After the main switch is first turned on, all the
displays come on as a test. After a few sec-
onds, the gauge will change to normal oper-
ation.
For more information, see the operation
manual originally supplied with the meter.

 

EMU31632

 

Command link multifunction 

fuel management meters

 

The fuel management meter has the func-
tions of fuel flow meter, total consumption
display, fuel economy display, and remain-
ing fuel display. The chosen display is select-
ed by using the “

” (set) and “

” (mode)

buttons as described in this section. For
more information, see the operation manual
originally supplied with the meter.
After the main switch is first turned on, all the
displays come on as a test. After a few sec-
onds, the gauge will change to normal oper-

 

2. Mode button

1. Speedometer
2. Fuel meter
3. Multifunction display

1

2

3

ZMU05435

 

1. Set button
2. Mode button

1. Speedometer
2. Fuel meter
3. Multifunction display

2

1

ZMU05436

1

2

3

ZMU05437

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды