Yamaha F300 Скачать руководство пользователя | Manualshive

Страница: 44 / 124

background image

Components

38

EMU26153

Power trim and tilt switch on bottom
engine cowling

The power trim and tilt switch is located on
the side of the bottom engine cowling. Press-
ing the switch “

” (up) trims the outboard

motor up, and then tilts it up. Pressing the
switch “

” (down) tilts the outboard motor

down and trims it down. When the switch is
released, the outboard motor will stop in its
current position.
For instructions on using the power trim and
tilt switch, see page 79.

WARNING

EWM01030

Use the power trim and tilt switch located
on the bottom engine cowling only when
the boat is at a complete stop with the en-
gine off. Attempting to use this switch
while the boat is moving could increase
the risk of falling overboard and could
distract the operator, increasing the risk
of collision with another boat or an obsta-

cle.

EMU35851

Power trim and tilt switches

The power trim and tilt system adjusts the
outboard motor angle in relation to the tran-
som. Pushing the switch “

” (up) trims the

outboard motor up, and then tilts it up. Press-
ing the switch “

” (down) tilts the outboard

motor down and trims it down. When the
switch is released, the outboard motor will
stop in its current position.

ZMU05822

UP

DN

UP

DN

ZMU05823

UP

DN

1

1

1

UP

DN

ZMU05835

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
42
43
44
45
46
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: SOLTEK Страницы: 72

Analog Devices DC2605A

Бренд: Linear Страницы: 16

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

Бренд: Texas Instruments Страницы: 16

Бренд: JETWAY Страницы: 2

Fatal1ty 990FX Professional

Бренд: ASROCK Страницы: 287

Бренд: Nuvoton Страницы: 5

Бренд: CHAINTECH Страницы: 59

Бренд: Gigabyte Страницы: 136

SERVER SYSTEM SR2500AL

Бренд: Intel Страницы: 210

Бренд: OLIMEX Страницы: 13

Бренд: Merit Страницы: 4

Бренд: EVGA Страницы: 1

880GM-LE - V1.0

Бренд: ASROCK Страницы: 60

Бренд: Apex Digital Страницы: 5

Бренд: TYAN Страницы: 100

Бренд: ASROCK Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды