manualshive.com logo in svg

Yamaha F300, Руководство пользователя

Поделиться
Скачать
Yamaha F300 Скачать руководство пользователя страница 39

 

Components

 

33

WARNING

 

EWM01770 

 

●

 

If the friction is too small, the control le-
ver could move freely and cause an ac-
cident.

 

●

 

Do not overtighten the friction adjuster.
If there is too much resistance, it could
be difficult to move the control lever,

 

which could result in an accident.

Single type

Single type

Twin type

Triple type

 

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

 

EMU35710

 

Station selector switch

 

The station selector switch can select either
the main station or sub station for the digital
electronic control which operates the boat.
The digital electric controls of the main sta-
tion and sub station have the same func-
tions. You can change the station when the
main switch is turned to “

” (on) and all con-

trol levers are in Neutral.
The switch panel can be operated at both the
main station and sub station when the main
switch is set to “

” (on).

ZMU06233

ZMU05820

ZMU05819

ZMU05963

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды