Yamaha F300 страница 82 Скачать руководство пользователя | Manualshive

Страница: 82 / 124

background image

Operation

76

EMU27821

Stopping engine

Before stopping the engine, first let it cool off
for a few minutes at idle or low speed. Stop-
ping the engine immediately after operating
at high speed is not recommended.

EMU35801

Procedure for single station models

1.

Turn the main switch to “

” (off).

2.

Remove the key if the boat will be left
unattended.

TIP:

The engine can also be stopped by pulling
the cord and removing the clip from the en-
gine shut-off switch, then turning the main
switch to “

” (off).

EMU35930

Procedure for dual station models
(main station)

1.

The procedure until stopping the engine
is the same as that of the single station
models.

2.

Remove the key if the boat will be left
unattended.

TIP:

The engine can also be stopped by pulling
the cord and removing the clip from the en-
gine shut-off switch, then turning the main
switch to “

” (off).

EMU35910

Procedure for dual station models
(sub station)

Push and hold the red engine stop button un-
til the engine comes to a complete stop.
When the engine has been stopped from the
sub station, be sure to turn the main switch
on the main station to “

”.

ZMU06247

ON

OFF

START

ON

OFF

START

ZMU04599

OFF

OFF

ON

ON

ZMU05833

OFF

OFF

ON

ON

OFF

ON

ZMU06014

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
80
81
82
83
84
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: SurfLink Страницы: 9

Бренд: Merit Страницы: 4

Z370 AORUS Gaming 7

Бренд: Gigabyte Страницы: 48

Бренд: XFX Страницы: 120

Бренд: ON Semiconductor Страницы: 22

Fatal1ty Professional Z97

Бренд: ASROCK Страницы: 144

Бренд: Biostar Страницы: 40

Бренд: NXP Semiconductors Страницы: 19

Бренд: Aaeon Страницы: 139

Бренд: Gigabyte Страницы: 96

Бренд: A-Trend Страницы: 49

Бренд: Lenovo Страницы: 51

Бренд: ASROCK Страницы: 190

Бренд: Abit Страницы: 96

Бренд: Digilent Страницы: 19

Бренд: Digilent Страницы: 32

Taichi Razer Edition B550

Бренд: ASROCK Страницы: 234

EMX-IG41D3-Icafe

Бренд: EMAXX Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды