Yamaha F300 Скачать руководство пользователя

Страница: 103 / 124

Maintenance

EMU29173

Checking propeller

WARNING

EWM01880

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

●

Before inspecting, removing, or install-
ing the propeller, place the shift control
in neutral, turn the main switch to “

”

(off) and remove the key, and remove
the clip from the engine shut-off switch.
Turn off the battery cut-off switch if

your boat has one.

Do not use your hand to hold the propeller
when loosening or tightening the propeller
nut. Put a wood block between the anti-cavi-
tation plate and the propeller to prevent the
propeller from turning.

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines for wear or damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-
age.

EMU30661

Removing propeller

EMU29197

Spline models

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

WARNING! Do

not use your hand to hold the propel-
ler when loosening the propeller nut.

[EWM01890]

Remove the propeller, washer (if
equipped), and thrust washer.

ZMU01897

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды