Yamaha F300 Скачать руководство пользователя

Страница: 95 / 124

Maintenance

EMU34445

Maintenance chart 1

TIP:

●

Refer to the sections in this chapter for explanations of each owner-specific action.

●

The maintenance cycle on these charts assume usage of 100 hours per year and regular
flushing of the cooling water passages. Maintenance frequency should be adjusted when
operating the engine under adverse conditions such as extended trolling.

●

Disassembly or repairs may be necessary depending on the outcome of maintenance
checks.

●

Expendable or consumable parts and lubricants will lose their effectiveness over time and
through normal usage regardless of the warranty period.

●

When operating in salt water, muddy, other turbid (cloudy), acidic water, the engine should
be flushed with clean water after each use.

The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

20 hours

months)

100

hours (1

year)

300

hours (3

years)

500

hours (5

years)

Anode(s) (external)

Inspection or replace-
ment as necessary

Anode(s) (exhaust
joint, cylinder head,
thermostat cover)

Inspection or replace-
ment as necessary

Anodes (exhaust joint
(inside), body cylinder,
Rectifier Regulator
cover)

Replacement

Anode(s) (casecrank
cover, upper case,
exhaust cover, cover
joint)

Replacement

Battery (electrolyte
level, terminal)

Inspection

Battery (electrolyte
level, terminal)

Fill, charging or replac-
ing as necessary

Cooling water leakage

Inspection or replace-
ment as necessary

Cowling clamp

Inspection

Engine starting condi-
tion/Noise

Inspection

Engine idling speed/
Noise

Inspection

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды