Yamaha F300 страница 117 Скачать руководство пользователя

Страница: 117 / 124

Trouble Recovery

111

11. Connect the water detection switch cou-

pler securely until a click is heard.

12. Securely attach the water detection

switch coupler to the holder.

13. Connect the lead to the holder.

14. Install the top cowling.
15. Start the engine and make sure that the

water separator-alert indicator remains
off. Have a Yamaha dealer inspect the
outboard motor after returning to port.

EMU33501

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.

NOTICE:

Do not attempt to run the

outboard motor until it has been com-
pletely inspected.

[ECM00401]

Bolt tightening torque:

8.0 Nm (0.8 kgf-m, 5.8 ft-lb)

1. Water detection switch coupler

ZMU05895

ZMU05897

ZMU05898

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды