Yamaha F300 Скачать руководство пользователя | Manualshive

Страница: 91 / 124

background image

85

Maintenance

EMU31841

Transporting and storing

outboard motor

WARNING

EWM01860

Leaking fuel is a fire hazard. When trans-
porting and storing the outboard motor,
close the fuel cock to prevent fuel from
leaking. Never get under the engine while
it is tilted. Severe injury could occur if the

outboard motor accidentally falls.

NOTICE

ECM00660

Do not use the tilt support lever or knob
when trailering the boat. The outboard
motor could shake loose from the tilt sup-
port and fall. If the motor cannot be trail-
ered in the normal running position, use
an additional support device to secure it

in the tilt position.

The outboard motor should be trailered and
stored in the normal running position. If there
is insufficient road clearance in this position,
then trailer the outboard motor in the tilt po-
sition using a motor support device such as
a transom saver bar. Consult your Yamaha
dealer for further details.

EMU35410

Storing outboard motor

When storing your Yamaha outboard motor
for prolonged periods of time (2 months or
longer), several important procedures must
be performed to prevent excessive damage.
It is advisable to have your outboard motor
serviced by an authorized Yamaha dealer
prior to storage. However, you, the owner,
with a minimum of tools, can perform the fol-

lowing procedures.

NOTICE

ECM01720

Store the outboard motor in a dry, well-

ventilated place, not in direct sunlight.

TIP:

The last time you use your Yamaha outboard
motor before storing it for a prolonged peri-
od, add one ounce of Yamaha Fuel Condi-
tioner and Stabilizer to each gallon of fuel in
the fuel tank.
Keep the outboard motor in the attitude
shown when transporting and storing it.

EMU28303

Procedure

EMU31921

Conditioning and stabilizing fuel

Fill the fuel tank with fresh fuel and add one
ounce of “Yamaha Fuel Conditioner and Sta-
bilizer” to each gallon of fuel.

TIP:

The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is
to be drained instead.

EMU31392

Washing the outboard motor

TIP:

This procedure is performed while the top
cowling is installed.

ZMU05843

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
89
90
91
92
93
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: AOpen Страницы: 8

CYTVII-B-E-1M-SK

Бренд: Cypress Страницы: 19

Бренд: Aeroflex Страницы: 20

Бренд: QDI Страницы: 23

Бренд: ASROCK Страницы: 198

Бренд: Gigabyte Страницы: 100

Бренд: Emcore Страницы: 12

PCAN-MicroMod Evaluation Kit

Бренд: Peak Страницы: 18

Бренд: IEI Technology Страницы: 160

Freescale MC9S08MM128

Бренд: NXP Semiconductors Страницы: 12

Бренд: XMOS Страницы: 20

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

Бренд: Supermicro Страницы: 229

Бренд: Acorp Страницы: 54

OPTIREG PMIC TLF30682QVS01

Бренд: Infineon Страницы: 24

Бренд: Asus Страницы: 112

Бренд: Asus Страницы: 62

Бренд: Asus Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды