Yamaha F300 страница 92 Скачать руководство пользователя | Manualshive

Страница: 92 / 124

background image

Maintenance

86

1.

Wash the outboard motor body using
fresh water.

NOTICE:

Do not spray wa-

ter into the air intake.

[ECM01840]

2.

Drain the cooling water completely out
of the motor. Clean the body thoroughly.

EMU28402

Lubrication

1.

Install the spark plug(s) and torque to
proper specification. For information on
spark plug installation, see page 93.

2.

Change the gear oil. For instructions,
see page 98. Inspect the oil for the pres-
ence of water that indicates a leaky seal.
Seal replacement should be performed
by an authorized Yamaha dealer prior to
use.

3.

Grease all grease fittings. For further de-
tails, see page 92.

TIP:

For long-term storage, fogging the engine
with oil is recommended. Contact your
Yamaha dealer for information about fogging
oil and procedures for your engine.

EMU30266

Cleaning and anticorrosion
measures

1.

Wash down the exterior of the outboard
motor with fresh water and dry off com-
pletely.

NOTICE:

Do not spray water

into the air intake.

[ECM01840]

2.

Spray the outboard motor exterior with
“Yamaha Silicone Protectant”.

NOTICE:

Do not spray when the engine is run-
ning. Also, do not spray near the si-
lencer or into the engine. Otherwise
the engine could be damaged.

[ECM01402]

3.

Wax the cowling with a non-abrasive
wax such as “Yamaha Silicone Wax”.

EMU28443

Flushing power unit

Perform this procedure right after operation

for the most thorough flushing.

NOTICE

ECM01530

Do not perform this procedure while the
engine is running. The water pump may
be damaged and severe damage from

overheating can result.

1.

After shutting off the engine, unscrew
the garden hose connector from the fit-
ting on the bottom cowling.

2.

Screw the garden hose adapter onto a
garden hose, which is connected to a
fresh water supply, and then connect it
to the garden hose connector.

3.

With the engine off, turn on the water tap
and let the water flush through the cool-
ing passages for about 15 minutes. Turn

1. Fitting
2. Garden hose adapter
3. Garden hose connector

1

2

3

ZMU05844

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
90
91
92
93
94
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: A-Trend Страницы: 40

Бренд: Garz Fricke Страницы: 35

661FX7MJ Series

Бренд: Foxconn Страницы: 81

Бренд: Gigabyte Страницы: 51

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: Avalue Technology Страницы: 82

Бренд: Texas Instruments Страницы: 14

Бренд: Ublox Страницы: 18

Бренд: NXP Semiconductors Страницы: 12

Бренд: ECS Страницы: 70

Бренд: JETWAY Страницы: 19

Бренд: Texas Instruments Страницы: 15

Бренд: Caji Страницы: 19

Бренд: ASROCK Страницы: 40

Бренд: Gigabyte Страницы: 39

Бренд: Gigabyte Страницы: 23

Бренд: Gigabyte Страницы: 147

Бренд: Zeal-All Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды