Yamaha F300 Скачать руководство пользователя | Manualshive

Страница: 67 / 124

background image

Operation

61

EMU35750

Change of station

For dual station boats, the station selector
switch can select either the main station or
sub station for the operating seat.
Only the selected station can operate the
digital electronic control. The switch panel
can start and stop the engine at both sta-
tions, regardless of the selected station.
1.

Set all control levers to Neutral.

2.

Turn the main switch to “

” (on).

3.

Push the station selector switch to select
the station for operating the boat.

4.

The digital electronic control-active indi-
cator for the selected station lights.

EMU27492

Starting engine

WARNING

EWM01600

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the wa-

ter near you.

EMU35866

Procedure for single station models

WARNING

EWM01840

●

Failure to attached engine shut-off cord
could result in a runaway boat if opera-
tor is ejected. Attach the engine shut-
off cord to a secure place on your cloth-
ing, or your arm or leg while operating.
Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

●

Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power,
the boat could slow rapidly. This could
cause people and objects in the boat to

be thrown forward.

1.

Place the control lever in “ ” (neutral).

TIP:

The start-in-gear protection device prevents
the engine from starting except when in neu-
tral.

1. Arrow

ZMU05976

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
65
66
67
68
69
...
»

Содержание F300





























































































































Отзывы:

Нет отзывов

Похожие инструкции для F300

Бренд: Linear Technology Страницы: 16

MBATX-845GV-VEAH

Бренд: Kontron Страницы: 70

Бренд: ASROCK Страницы: 56

Бренд: Biostar Страницы: 23

Бренд: Aaeon Страницы: 44

Бренд: BiPOM Electronics Страницы: 12

Бренд: IWILL Страницы: 48

Бренд: Texas Instruments Страницы: 11

Бренд: CHAINTECH Страницы: 49

Бренд: BOSER Technology Страницы: 38

Бренд: Gigabyte Страницы: 96

SUPERO X10DRU-X

Бренд: Supermicro Страницы: 109

STEVAL-IHM011V1

Бренд: ST Страницы: 27

K9AG Neo2-Digital

Бренд: MSI Страницы: 103

Бренд: Kontron Страницы: 49

Бренд: Kontron Страницы: 68

80486 Deep Green

Бренд: VESA Страницы: 47

MAX 10 FPGA 10M50

Бренд: Altera Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды