Yamaha F300 страница 73 Скачать руководство пользователя

Страница: 73 / 124

Operation

shut-off switch.

EMU35880

Selecting outboard motor

(triple engine)

After all engines have started, set all control
levers to Neutral. Push the engine selector
switch repeatedly to change the digital elec-
tronic control-active indicator and select the
desired engine.

First, three engines can be operated.

TIP:

When all engines have started, the center
engine will run at the average speed of port
side and starboard side engines’ speeds.

●

Operate the port side engine using the port
side control lever.

●

The center engine runs at the average
speed of port side and starboard side en-
gines’ speeds.

●

Operate the starboard side engine using
the starboard side control lever.

Push the engine selector switch once to
operate the port side and starboard side
engines.

1. Port side control lever
2. Starboard side control lever
3. Port side engine
4. Center engine
5. Starboard side engine

ZMU05998

ZMU05999

ZMU06000

ZMU06001

2019 Yamaha Motor Corporation, U.S.A.

Содержание F300





























































































































Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды

Yamaha F300, Руководство пользователя

Результаты поиска

Содержание F300

Отзывы:

Похожие инструкции для F300

Бренды по названию

Популярные бренды